Uninet White DTF PreTreat Powder (1 lb / 2 lbs)

Uninet White DTF PreTreat Powder

DTF Transfer Adhesive Powder - works with all DTF printers utilizing DTF ink and DTF PreTreat Sheets or Rolls.

WHITE DTF POWDER is best for use with WHITE or LIGHT colored garments. The white powder works in the same way that black powder does. When using on a white or light colored garment, any stray adhesive that may have been left on the transfer sheet will blend in with the color of the shirt.

(BLACK DTF POWDER is best for use with BLACK or DARK colored garments).

*This product is excluded from all promotional discounts and offers.

• Uninet DTF Transfer Adhesive Powder is a proprietary, specially formulated Thermoplastic Polyurethane (TPU) Hot Melt Adhesive Powder, also referred to as 'PreTreat' powder.
• DTF TRANSFER is accomplished using DTF Transfer Sheets and DTF Transfer Powder.
• First, print to DTF Transfer Sheets or Rolls; then cover your print with DTF Adhesive Powder powder and cure; and finally heat press it to your garments or textiles.

When using the heat station (manual process):
• After you print, you must apply the adhesive power within a few minutes (before the ink dries). Manual application of the powder would normally a require large container, spreading the powder all over the page, and then removing as much excess powder as possible by ‘flicking’ the back of the sheet.
• Then lay the print in the heat station, print side face up.

Recommended temperature for DTF powder curing:
• A3 sheets – 120°C / 250°F for 120 seconds. For sheets with large images and / or a lot of ink coverage, it may be necessary to open the cover, rotate the page 180 degrees, and then bake again for another 2 mins.
• A4 or smaller sheets - 120°C / 250°F for 120 seconds

Application to substrate:
• Recommended Heat Press Pressure: Medium or 60 lbs of pressure
• Place or thread your garment on the press. Position the transfer sheet (print side down) onto the garment. Cover the transfer sheet and garment with kraft paper and close the press, using the following suggestions:

COTTONS and BLENDS: • Press at 300 - 325°F for 10 – 12 seconds • Post press for 5 – 10 seconds *Hoodies may require 325°F and up

POLYESTERS / TRI-BLENDS: • 265 – 275°F for 8 – 10 seconds • Post press for 5 – 10 seconds * Thinner material may require lighter pressure; otherwise the transfer can leave a ‘window’ on the garment and/or scorching may occur. *Polyester settings can vary, but best to use lower temperature and pressure generally

50 / 50: • 275°F for 12 seconds • Post press for 5 – 10 seconds

COTTON: • 310 - 325°F for 15 seconds • Post press for 10 seconds

FINISHING: • Matte finish – Kraft paper, T Seal or parchment cover sheet. • Shiny/gloss finish - Teflon cover sheet *Specialty silicone pads with texture can be used to prevent gloss look, gives print a nice textured feel.

ADDITIONAL SUGGESTIONS: • Thicker fabrics require more heat, generally. • Hats (poly) may require 245 - 250°F for 5 - 8 seconds • Umbrellas, EZ-ups, stadium chairs will require testing and trial and error. *Be careful of dye / ink migration with polyester textiles - perform a 24hr test (fine tuning) to see if the ink migrates (clothing dye reacts with the DTF ink)

GARMENT TYPES: • DTF works with almost all fabrics and garment types: • Combed Cotton, Ring Spun Cotton, Organic Cotton, Polyesters, Blended Fabrics, Poly-Cottons, Tri-Blends, Polyester-Spandex, Leather, Vinyl, Denim, Canvas and much more.